In addition to replacing the spark plugs at the manufacturer's recommended intervals, spark plugs should be removed, inspected and cleaned (if necessary) every 5,000 miles.  The tips below can be used on all spark plugs whether they are on your motorcycle, car, boat, or event your lawn mower.
 

If the plugs exhibit normal wear as indicated in picture #1, you can simply clean and re-use the same plugs. If the spark plugs exhibit extreme wear or any of the wear features pictured below, the plugs should be replace and the necessary repairs adjustments should be made to the motor.

To clean the plugs simply remove all debris with a fine piece of sand paper, rinse with gasoline or engine cleaner, check the plug gap (adjust if necessary) and re-install.


 

Normal Spark Plug Wear

This plug has been running at the correct temperature in a "healthy" engine. Operating in such a desirable environment results in deposits that will be light tan or gray in color with most grades of commercial gasoline. Spark plugs demonstrating normal wear should still be changed at the manufacturers recommended intervals.


 

 

---

Carbon Fouled Spark Plug

Basically, soft, sooty carbon deposits, as shown , have a dry, black appearance. Often indicates bad ignition wires, an incorrect heat range spark plug or an over-rich air/fuel mixture caused by a clogged air cleaner filter element, or a faulty choke. Fuel injectors that malfunction can also lead to this condition.

Other less common causes include weak ignition system voltage or poor cylinder compression.



 

---

Pre-Ignition

As shown , this condition produces melting of the center electrode, and somewhat later, the ground electrode and insulator. Usually one or a combination of several engine operating conditions are the prime causes of pre-ignition. It may originate from glowing combustion chamber deposits, hot spots in the combustion chamber due to poor control of engine heat, cross-firing (electrical induction between spark plug wires), or the plug heat range is too high for the engine or its operating conditions.


 

---

Overheated

Note the dead white or gray insulator nose which appears "blistered." Electrode gap wear rate will be considerably in excess of that normally expected. This is often caused by overadvanced ignition timing, poor engine cooling, a very lean A/F mixture, a leaking intake manifold, or the use of a spark plug too hot for the application.


 

 

---

Mechanical Damage

Mechanical damage to the firing end, as shown, is caused by some foreign object in the combustion chamber or the plug nose is too long for the engine (incorrect plug selection). Since small objects can travel from one cylinder to another (because of valve overlap), the other cylinders should always be checked to prevent reoccurrence of damage.

 

 

---

Oiled Fouled

A spark plug shorted by excessive oil entering the combustion chamber is shown. This is often caused by piston rings or cylinder walls that are badly worn. Oil may also be pulled into the chamber because of excessive clearance in the valve stem guides, or badly worn valve stem seals.


 

 

---

Broken/Cracked Insulator

Typically caused by improper handling of the spark plug prior to or during installation. Broken insulators can also be caused by severe detonation. Major causes include a lean air/fuel mixtures, ignition timing advanced too far, and insufficient octane rating of the gasoline.

 

Very nice . Great maintance tip

DITTO Thanks for the posting.

got new plugs a few months back ,my kawasaki dealer was wanting £40 for 4 plugs .got them from a lawnmore site for for about £10 ,same things .

another GREAT TIP ,look at lawnmore site's first lol.

Good stuff. One thing to mention on spark plugs, is how the altitude effects the bike and spark plug wear. If your Harley Davidson, or any motorcycle for that matter, is carburated and tuned for lower altitudes, you will almost definitely experience the Carbon Fouled Spark Plugs seen above. Really no way around it unless you have the carb re-tuned. So my suggestion is to carry some spare plugs and a spark plug wrench if you are planning on some mountain riding.

To answer your question should you clean them-NO.if you leave just a tiny pit of crap on the plug and put it backin you are putting that crap directly into the cylinder and that is not good.Take um out and look at them if you want to but don't clean them in my opinion.

good tips

Also keep in mind that most heads now are aluminum. Let the engine cool all the way down before removing them. Apply just a touch of antiseize to the threads when installing them. Don't over torque but above all do not under torque! If they do not seal, then gas's get by the threads and get carbon in them and next time you go to pull them out they bind and it you force them out you will take the threads with them.

Also if you have a newer bike with Platinum plugs and fuel injection, you only need to do this every 18-20k.

If you have dirty plugs and are having misfire due to say wet weather and water getting sucked in through your carb(older bikes here) if you carry one of those metal nail files wimmen usually have you can whip out the plugs and give them a quick clean that will get you home.
I only ever had to do it once and that was about a mile from home after three hours of monsoon type rain.

Using premium fuel how many miles do plugs last in a late model Harley?

Well the manual says to inspect every 5,000 and replace every 20,000. With a well tuned bike and good clean fuel, I imagine 20,000 would be fine. I normally change mine when if I am going on a long haul and they have more than 10,000 on them, so I have never really pushed it to the limit to see how far you can go.

Excellent, I'm a believer in premium, use it in everything, generators, chain saws, vehicles. Storage is forever can let the generator sit six months and start right up. Regular fuel and spark plugs don't get along been my experience. I bought a new 88 Chevy van with a 305 in it, used premium for over 100000 miles, felt guilty one day and spent a couple hundred bucks on plugs, cap, wires, all that stuff. Pulled the plugs for the first time and they looked fine. After installing everything it still ran the same, no difference, purred like a kitten. lol